6 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 6 / 6
Yayın Thermal quenching of thermoluminescence in quartz samples of various origins(Univ Agean, Dept Mediterranean Stud, 2010) Subedi, Bhagawan; Afouxenidis, Dimitrios; Polymeris, George S.; Bakoglidis, Konstantinos D.; Raptis, Spyridoula; Tsirliganis, Nestor C.; Kitis, GeorgeThe effect of thermal quenching plays an important role in the thermoluminescence (TL) of quartz on which many applications of TL are based. In present work it is investigated that the thermal quenching parameters i.e. the activation energy W and the dimensionless parameter C, are more or less the same for every kind of quartzes or sample dependent on strong external treatment like a high temperature annealing. This preliminary investigation of seven quartz samples of different origin showed that the thermal quenching parameters W and C are common (universal) for most of the quartz samples.Yayın Preliminary TL and OSL investigations of obsidian samples(Univ Agean, Dept Mediterranean Stud, 2010) Polymeris, George S.; Gogou, D.; Afouxenidis, Dimitrios; Rapti, Sofia; Tsirliganis, Nestor C.; Kitis, GeorgeObsidian is a volcaniclastic mineral extremely hard to break, which was used in prehistoric Greece (and elsewhere in the World), in order to provide tools, weapons, knives and arrowheads. The present work aims to characterize this extremely precious tool stone by using both thermoluminescence (TL) and optically stimulated luminescence (OSL) techniques and investigate its potential use for luminescence dating purposes. Basic TL and OSL properties, such as TL and OSL thermal and optical stability, repeatability, TL and LM-OSL glow curve shape and mainly the linearity of the TL and OSL signals as a function of beta dose were investigated. Artificially irradiated samples indicate all promising luminescence features, such as the 110 degrees C TL peak and dose response sub-linearity for intermediate doses, quick and effective bleaching all over the entire TL glow curve, along with quite linear CW-OSL dose response for doses larger than 5 Gy. The lack of predose sensitisation indicates the suitability of the material for single aliquot measurements. Furthermore, several features provide indications that the signal does not relate to quartz, but in fact to other silicates. Unfortunately, both lack of bleaching ability for NIL signal, along with a peculiar shape of NOSL, provide major difficulties in dating applications.Yayın Thermoluminescence as a probe in bioactivity studies; the case of 58S sol-gel bioactive glass(IOP Publishing Ltd, 2011-10-05) Polymeris, George S.; Goudouri, Ourania Menti; Kontonasaki, Eleana; Paraskevopoulos, Konstantinos M.; Tsirliganis, Nestor C.; Kitis, GeorgeThe formation of a carbonated hydroxyapatite (HCAp) layer on the surface of bioactive materials is the main reaction that takes place upon their immersion in physiological fluids. To date, all techniques used for the identification of this HCAp formation are rather time consuming and not well suited to detailed and rapid monitoring of changes in the bioactivity response of the material. The aim of this work is to explore the possibility of using thermoluminescence (TL) for the discrimination between different bioactive responses in the case of the 58S bioactive glass. Results provided strong indications that the 110 degrees C TL peak of quartz can be used effectively in the study of the bioactive behaviour of 58S bioactive glass, since it is unambiguously present in all samples and does not require deconvolution analysis. Furthermore, the intensity of the 110 degrees C TL peak is proven to be very sensitive to the different bioactive responses, identifying the loss of silica which takes place at the first stages of the sequence. The discontinuities of the 110 degrees C TL peak intensity plot versus immersion time at 8 and 1440 min provide experimental indications regarding the timescale for both the beginning of amorphous CaP formation as well as the end of crystalline hydroxyl-apatite formation respectively, while the spike in the sensitization of the 110 degrees C TL peak, which was observed for immersion times ranging between 20 and 40 min, could be an experimental feature indicating the beginning of the crystalline HCAp formation.Yayın In-homogeneity in the pre-dose sensitization of the 110 degrees C TL peak in various quartz samples: The influence of annealing(Elsevier Science BV, 2012-03-01) Polymeris, George S.; Oniya, Ebenezer O.; Jibiri, Nnamdi N.; Tsirliganis, Nestor C.; Kitis, GeorgeThe pre-dose sensitization effect of the 110 degrees C TL glow-peak of quartz is a basic tool in thermoluminescence and optically stimulated luminescence dating and retrospective dosimetry. In the present work, a homogeneity study was performed on pre-dose sensitization in grains obtained from large quartz crystals samples collected from 10 different origins. The aliquot - to - aliquot scatter of the pre-dose sensitization of the 110 degrees C TL peak within each quartz crystal was monitored. The influence of the annealing on this scattering was also studied. Therefore, the investigation was applied to the un-fired "as is" samples as well as to samples annealed at 900 degrees C for 1 h following cooling to room temperature in air. The results showed that in the case of "as is" quartz the sensitization effect vary strongly within each aliquot of the same quartz sample. This strong variation is removed by both the high temperature annealing as well as heating up to 500 degrees C, involved in the TL measurements. These results are generally discussed in the framework of existing models and applications of the effect.Yayın Reconstruction of thermally quenched glow curves in quartz(Pergamon-Elsevier Science Ltd, 2012-04) Subedi, Bhagawan; Polymeris, George S.; Tsirliganis, Nestor C.; Pagonis, Vasilis; Kitis, GeorgeThe experimentally measured thermoluminescence (TL) glow curves of quartz samples are influenced by the presence of the thermal quenching effect, which involves a variation of the luminescence efficiency as a function of temperature. The real shape of the thermally unquenched TL glow curves is completely unknown. In the present work an attempt is made to reconstruct these unquenched glow curves from the quenched experimental data, and for two different types of quartz samples. The reconstruction is based on the values of the thermal quenching parameter W (activation energy) and C (a dimensionless constant), which are known from recent experimental work on these two samples. A computerized glow-curve deconvolution (CGCD) analysis was performed twice for both the reconstructed and the experimental TL glow curves. Special attention was paid to check for consistency between the results of these two independent CGCD analyses. The investigation showed that the reconstruction attempt was successful, and it is concluded that the analysis of reconstructed TL glow curves can provide improved values of the kinetic parameters E, s for the glow peaks of quartz. This also leads to a better evaluation of the half-lives of electron trapping levels used for dosimetry and luminescence dating.Yayın Thermal quenching of thermoluminescence in quartz samples of various origin(Elsevier Science BV, 2011-03-15) Subedi, Bhagawan; Oniya, Ebenezer O.; Polymeris, George S.; Afouxenidis, Dimitrios; Tsirliganis, Nestor C.; Kitis, GeorgeThe effect of thermal quenching stands among the most important properties in the thermoluminescence (TL) of quartz on which many applications of TL are based. Since the quartz samples used in various applications are all of different origin it is useful to investigate whether the values of the thermal quenching parameters, i.e. the activation energy for thermal quenching W and a parameter C which describes the ratio of non-radiative to radiative luminescence transitions, evaluated mainly in specific quartz samples can be extrapolated to quartz samples of unknown origin as well as to quartz samples which are annealed at high temperatures. In the present work the TL glow curve of a series of un-annealed and annealed natural and synthetic quartz samples were studied as a function of the heating rate between 0.25 K/s and 16 K/s. Using an indirect fitting method it was found that the thermal quenching parameters W and C in most of the quartz samples are very similar to the values accepted in the literature. Furthermore, in some cases the thermal quenching parameters Wand Care not the same for all TL glow-peaks in the same glow-curve. Finally, the strong external treatment of annealing the quartz samples at very high temperature can also influence at least one of the thermal quenching parameters.
